background image

11

EN

Installation

Bus controller installation

The 

TSB Controller II

 is intended for installation in a suitable electrical distributor.

It is mounted on top-hat rails according to DIN EN 60715 TH35. The wiring takes 
place via screw-type terminals.

The installation location of the 

TSB Controller II

 distributor must meet the follow-

ing conditions:

 · It must be on the inside of the building.
 · It must not be exposed to any unusual environmental conditions, such as ag-

gressive vapours or high humidity.

 · The 

TSB Controller II

 should be easily accessible in a protected area and not be 

exposed to direct sunlight.

 · When mounting the

 TSB Controller II

on the wall, take care not to damage any 

wiring or pipes inside the wall itself. The module rack for the 

TSB Controller II

 and 

fastening screws must not come into contact with conductive elements in the 
building’s structure. 

Power supply

The 

TSB Controller II

 must be powered by an external power supply.

The power supply unit must comply with the specifications described in chapter 
“Technical data”, page 22.

Installation 

location

external power 

supply

Summary of Contents for 970-TSBC-30-00

























Reviews: