manualshive.com logo in svg

Aspes AAS2009, Instruction Manual

Share
Download
Aspes AAS2009 Instruction Manual Download Page 25

Outdoor Unit 

Outdoor Unit Wiring Diagram  

is located on the inside of the 

wire cover on the outdoor unit.

Cover

W

arning

All wiring must performed strictly in accordaance with the wiring diagram located on the inside of the outdoor 

unit’s 

wire cover.

1. Prepare the cable for connection:

Use the right cable

       Indoor Power Cable (if applicable):  H05VV-F or H05V2V2-F

            Outdoor Power Cable:  H07RN-F

            Signal Cable:  H07RN-F

W

arning

Before performing any electrical or wiring work, turn off the main power to the system.

Do not let wires touch or rest against refrigerant tubing, the compressor, or any moving parts with the unit.

If the unit has an auxiliary electric heater, it must be installed at least 1 meter (40in) away from any 

combustible materials.   

a.Using wire strippers, strip the rubber jacket from both ends of signal cable to reveal about 40mm (1.57in)

of the wires inside.

b.Strip the insulation from the ends of the wires.

c. Using wire crimper, crimp u-type lugs on the ends of the wires.

Note:While crimping wires, make sure you clearly distinguish the Live (“L”) Wire from other wires.

2. Unscrew the electrical wiring cover and 

r

emove it.

3. Unscrew the cable clamp below the terminal block and place it to the side.

4. Match the wire colors/labels with the labels on the terminal block, and firmly screw the u-lug of each wire to its

corresponding terminal.

5. After checking to make sure every connection is secure, loop the wires around to prevent rain water from

flowing into the terminal.

6. Using the cable clamp, fasten the cable to the unit. Screw the cable clamp down tightly.

7. Insulate unused wires with PVC electrical tape.

Arrange them so that they do not touch any electrical or metal parts.

8. Replace the wire cover on the side of the unit, and screw it in place.

5. Outdoor Unit Installation

22

> 16 and ≤ 25

2.5

> 25 and ≤ 32

4

> 32 and ≤ 40

6

Minimum Cross-Sectional Area of Power and Signal Cables 

Rated Current of Appliance (A)

Nominal Cross-Sectional Area (mm²)

> 3 and ≤ 6

0.75

1

1.5

> 6 and ≤ 10
> 10 and ≤ 16

Summary of Contents for AAS2009





































Reviews:

No comments

Brands by name

Popular brands

Load more brands