background image

4

309420

WARNING

SKIN INJECTION HAZARD

High pressure fluid from gun, hose leaks, or ruptured components will pierce skin.  This may look like
just a cut, but it is a serious injury that can result in amputation.  

Get immediate surgical treatment.

D

Do not point gun at anyone or any part of the body.

D

Do not put your hand over the spray tip.

D

Do not stop or deflect leaks with your hand, body, glove, or rag.

D

Engage trigger lock when not spraying.

D

Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking or servicing equipment.

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

D

Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component.  Read 

Technical Data

 in all equipment manuals.

D

Use fluids and solvents that are compatible with equipment wetted parts.  Read 

Technical Data

 in

all equipment manuals.  Read fluid and solvent manufacturer’s warnings.  For complete information
about your material, request MSDS from distributor or retailer.

D

Check equipment daily.  Repair or replace worn or damaged parts immediately with genuine ASM
replacement parts only.

D

Do not alter or modify equipment.

D

Use equipment only for its intended purpose.  Call your Graco distributor for information.

D

Route hoses and cables away from traffic areas, sharp edges, moving parts and hot surfaces.

D

Do not kink or over bend hoses or use hoses to pull equipment.

D

Keep children and animals away from work area.

D

Do not operate the unit when fatigued or under the influence of drugs or alcohol.

D

Comply with all applicable safety regulations.

TOXIC FLUID HAZARD

Toxic fluid or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.

D

Read MSDS’s to know the specific hazards of the fluids you are using.

D

Store hazardous fluid in approved containers and dispose of it according to all applicable guide-
lines.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss.  This equipment includes, but is not limited to:

D

Protective eye wear.

D

Clothing and respirator as recommended by the fluid and solvent manufacturer.

D

Gloves.

D

Hearing protection.

Summary of Contents for Zip-Spray-n-Roll 233792

















































Reviews: