ASM Zip-Spray-n-Roll 233792 Operation, Repair, And Parts Download

Page: 34 / 48

309420

Advanced Troubleshooting

NOTE:

See

Basic Troubleshooting

on page 31 for the problems that are more easily remedied.

General Problem: Motor Does Not Operate

SPECIFIC PROBLEM

CAUSE

SOLUTION

Power switch is on and
sprayer is plugged in but

See

Basic Troubleshooting

page 31.

sprayer is plugged in, but
pump does not cycle.

Basic Mechanical
Problems

Paint is frozen or hardened in pump.

Unplug sprayer from electrical outlet.

NOTE: If frozen, do not try to start sprayer
until completely thawed

, or damage to motor,

control board, and/or drivetrain may occur.

Make sure power switch (B) is OFF. Place
sprayer in warm area for several hours, then
plug in and turn on. Slowly increase pressure
setting to see if motor starts.

If paint hardened in sprayer, replace pump
packings and remove all residue from valves.

See

Pump Service

on page 42.

Motor is damaged.

Remove gear, and try to rotate motor shaft by
hand. See

Motor Diagnostics

on page 41. If

shaft will not turn, replace motor using

Motor

Kit

245080.

Basic Electrical Problems

Motor is overheated.

Allow to cool for 30 minutes. Retry.

Electrical outlet is damaged.

Reset building circuit breaker or replace
building fuse. Try another outlet.

Check electric supply with volt meter. Meter
must read 85 to 130V AC. If voltage is too
high, do not plug sprayer in until outlet is
corrected.

Control board leads are improperly fastened or
improperly mated.

Replace any loose terminals. Make sure all
leads and harnesses are firmly connected.

Check pressure control harness connection on
front side of drive housing.

Clean control board terminals. Securely
reconnect leads.

Motor brushes are worn.

NOTE:

Brushes do not wear at the same rate on

both sides of motor. Check both brushes.

Check length of brushes. Brush length must
be 0.25 in. (6.4 mm) minimum. If brushes are
worn, replace motor using

Motor Kit

245080.

Motor armature commutator is damaged.

Check for burn spots, gouges and extreme
roughness. Have motor shop resurface
commutator if possible, or replace motor using

Motor Kit

245080.

Summary of Contents for Zip-Spray-n-Roll 233792

















































Search results

Summary of Contents for Zip-Spray-n-Roll 233792

Reviews:

Related manuals for Zip-Spray-n-Roll 233792

Brands by name

Popular brands

ASM Zip-Spray-n-Roll 233792, Operation, Repair, And Parts

Search results

Summary of Contents for Zip-Spray-n-Roll 233792

Reviews:

Related manuals for Zip-Spray-n-Roll 233792

Brands by name

Popular brands