Asko ADA Series Installation Instructions Manual Download

Page: 20 / 20

INSTALLATION CHECKLIST

ASKO - DISHWASHER

Appliance Installation Checklist

• Remove packaging and check for cosmetic damages.

• Remove the information packets from inside the dishwasher.

• Attach any accessories as required by the installation. Fill strips, light shielding

film, supplied door sealing, accessory door, custom panel...

• Attach the drain line using the largest section of the disposer boot allowable.

Leave the high loop in place.

• Attach the PEX fill hose. Don’t forget to use the O-ring.

• Plug the dishwasher into the wall.

• Turn on the water and check the fill line connections for leaks.

• Slide the unit into the cabinet and level the machine front to rear, and left to right.

• Mount the unit to the cabinet.

• Turn the power to the unit on and start a cycle. Make sure there are no drain

leaks.

• Show the customer their warranty card, and help them locate the model and

serial number on the unit.

• Leave all user books for consumer.

t. No 492181 Rev

. 03

CUSTOMER CARE CENTER 1-800-898-1879

• WWW.ASKONA.COM

492181 Install DW16 FI USA EN Rev 03.indd 20

2016-05-31 10:32:55

en (05-16)

Summary of Contents for ADA Series





















Search results

Summary of Contents for ADA Series

Reviews:

Related manuals for ADA Series

Brands by name

Popular brands

Asko ADA Series, Installation Instructions Manual

Search results

Summary of Contents for ADA Series

Reviews:

Related manuals for ADA Series

Brands by name

Popular brands