background image

Installation Instructions 

FI Dishwasher

INTRODUCTION ......................................................................................................................... 2

WHAT YOU NEED ...................................................................................................................... 2

SAFETY INSTRUCTIONS ............................................................................................................ 3

BEFORE STARTING THE INSTALLATION .................................................................................. 3 

XXL DISHWASHERS ................................................................................................................... 4

  – UNIT DIMENSIONS ............................................................................................................... 4

  – PREPARING THE LOCATION ................................................................................................ 4

ADA AND XL DISHWASHERS .................................................................................................... 5

  – UNIT DIMENSIONS ............................................................................................................... 5

  – PREPARING THE LOCATION ................................................................................................ 5

  – ADAFI TRIM KIT INSTALLATION OPTIONS .......................................................................... 6

STEP 1. FITTING THE DISHWASHER IN PLACE........................................................................ 7

STEP 2. ATTACHING THE ACCESSORY DOOR OR CUSTOM PANEL .................................... 10

STEP 3. ADJUSTING THE DOOR SPRINGS ............................................................................ 11

STEP 4. CONNECTING ELECTRICITY, WATER, AND DRAIN .................................................. 12

STEP 5. CHECKING DISHWASHER FUNCTION AND FIT ....................................................... 15

STEP 6. SECURING THE DISHWASHER.................................................................................. 15

STEP 7. ATTACHING THE TOE KICK (IF APPLICABLE) .......................................................... 17

INSTALLATION CHECKLIST ..................................................................................................... 20

CONTENTS

IMPORTANT! 

READ ALL OF THESE INSTRUCTIONS BEFORE INSTALLING THE DISHWASHER. 

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

492181 Install DW16 FI USA EN Rev 03.indd   1

2016-05-31   10:32:38

Summary of Contents for ADA Series





















Reviews: