cover
16 Grinding disc cover
17 Star grip nut to mount/adjust the workpiece support
grinding disc
18 Workpiece support grinding disc
19 Grinding disc
20 Upper (a) and lower (b) roller
21 Adjusting screw tape run
Accessories
3 pcs of sanding belt
PICTOgrAmS
Pictograms and values stated on the product
packaging:
a) Power values
b) Power consumption
c) No-load speed
d) Grinding belt
d) Grinding disc
a
b
c
d
e
USE AND OPErATION
The ASIST equipment and machines are designed for
domestic or hobby use only.
The manufacturer and the importer do not recommend
to use this equipment under extreme conditions and at
high loads. Any other additional requirements must be
agreed upon by the manufacturer and the buyer.
Assembly
Caution! Risk of injury!
- Ensure that you have sufficient space in which to
work, and that you do not endanger other people.
- Always fasten the device on to the work surface with
screws featuring the sufficient length and
thickness in order to maintai control of the device.
- All covers and protective devices must be assembled
properly before commissioning.
- Disconnect the mains plug before changing the set
-
ting on the device.
Assemble/set spark protection
1. Screw the spark protection (1) using the adjusting
screw (2) and the nut (2a) on to the protective
hood (3).
To do so, you will need a screwdriver and a ring span
-
ner, used to hold it in place.
2. Set the spark protection (1) with the adjusting screw
(2) so that the distance between the grinding
disc (19) and the spark protection is max. 2 mm (see
small image).
Periodically readjust the spark protection in order to
offset the wear and tear of the grinding disc (distance
max. 2 mm).
Assemble/set workpiece supports
1. Screw the workpiece supports (6/18) on to the de
-
vice.
2 positions (see A + B) are possible for the tape loop.
2. To do so, use the screws (5a/17a), washers
(5b/17b), toothed lock washer (5c/17c) and star grip
nuts (5/17) provided.
3. Set the workpiece support of the grinding belt (19)
with the star grip nut (17) so that the distance
between the grinding belt (19) and the workpiece
support is max. 2 mm (see small image).
Periodically readjust the workpiece support in order to
offset the wear and tear of the grinding disc (distance
max. 2 mm).
Screw device on to workbench
Screw the device onto the workbench with 4 screws
and nuts.
Insert the screws through the 4 bore holes (13) on the
base of the device.
The screws and nuts required for assembly are not
part of the scope of delivery.
Operation
Caution! Risk of injury!
- Always disconnect the plug from the mains socket
before working.
- Use only grinding disks and accessories recommen
-
ded by the manufacturer. The use of other insertion
tools and other accessories may cause risk of injury.
- Only use grinding tools which bear information about
the manufacturer, type of binding, dimension
and permitted number of revolutions.
- Only use grinding discs where the printed rotational
speed is at least as high as what has been
specified on the name plate of the device.
- Do not use broken, cracked or otherwise damaged
grinding disks.
- Never operate the device without the visual protec
-
tion disk.
- Always use protective goggles even if you are protec
-
ted against sparks.
- Always inspect the grinding disc before starting the
device:
Check the distance between the spark protection and
grindin disc as well as workpiece support and grinding
disc (distance maximum 2 mm).
- The grinding disc must be replaced once the spark
protectionand workpiece support on the grinding disc
do not have distance of max. 2 mm.
- Switch on the equipment only when it is safely in
-
stalled on the work surface.
Keep your hands away from the grinding disc and
grinding belt when the device is in operation. Injury
hazard!
Switching on and off
Ensure that the mains voltage matches the specificati
-
ons on the rating plate.
Connect the equipment to the mains.
1. To switch on, press the “I” On switch and the device
starts up (see 14a).
2. To switch off, press the “0” off switch and the device
52
