background image

CONTENT

Section 

Page

Preface 

1

Product Identification 

Product Features 

3

Installation 

4-10

Gas Piping 

11-12

Operation 

12-14

Cleaning and Maintenance 

14-15

Troubleshooting 

16-18

Service and Maintenance 

18

Parts List 

19-23

This gas appliance must not be connected to a chimney flue serving a separate solid-
fuel burning appliance.

IMPORTANT FOR YOUR SAFETY

·

Improper installation, adjustment, alteration, service, or maintenance can cause 
property damage, personal injury or loss of life.  Refer to this manual.

·

Installation and service must be performed by a qualified installer, service agency, or 
the gas supplier.

 

Do not use this appliance if any part has been under water.  Immediately call a qualified 
service technician to inspect the appliance and to replace any part of the control system 
and any gas control which has been under water.
Ne pas se servir de cet appareil s'il a été plongé dans l'eau, complètement ou en partie. 
Faire inspector l'appareil par un technicien qualifié et remplacer toute partie du système 
de contrôle et toute commande qui ont été plongées dans l'eau.

PRODUCT IDENTIFICATION

 

Figure 2

2

Summary of Contents for AGDV12

























Reviews: