ASCO POWER TECHNOLOGIES 360 Page 13 Installation & Operation Manual Download

Page: 13 / 16

For access to self-service tools and chat support visit se.com/us/en/work/support or call 1-888-778-2733 for technical assistance

IO-70067

01/2020

ASCO 360 Surge Protective Device (SPD)

Wiring

1. Select the location where the SPD and Flush Mount Kit (XMFMKIT) will

be mounted. Aesthetics may have to be sacrificed in order to achieve

maximum surge protection.

2. Place the Flush Mount Kit plate where it will be mounted and trace the

center hole and mounting holes. Cut this shape into the mounting sur-

face and mount the XMFMKIT panel to the mounting surface.

3. BE CAREFUL TO NOT DROP THE SPD INTO THE WALL.

4. Install the SPD to the back side of the Flush Mount Kit plate using the

four 8/32 x 5/8 in. Thread Cutting Screws provided with the XMFMKIT kit.

5. Proceed with #6 on page 12.

Flush Mount Installation

Instructions

Insert flushmount screw through

hole in each corner or punch a

small starting hole in center of each

translucent window (located in all 4

corners of the label).

Figure 3:

Typical Model 360 SPD installation (Dimensions - in./mm.)

Summary of Contents for 360

















Search results

Summary of Contents for 360

Reviews:

Related manuals for 360

Brands by name

Popular brands

ASCO POWER TECHNOLOGIES 360, Installation & Operation Manual

Search results

Summary of Contents for 360

Reviews:

Related manuals for 360

Brands by name

Popular brands