Asante AWRT-600N User Manual Download | Manualshive

Page: 58 / 61

background image

58

App Appendix – Information

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.  If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
-

Reorient or relocate the receiving antenna.

-

Increase the separation between the equipment and receiver.

-

Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

-

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. To maintain compliance with FCC RF exposure compliance
requirements, please follow operation instruction as documented in this manual.

This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.

SAR compliance has been established in typical laptop computer(s) with CardBus slot,
and product could be used in typical laptop computer with CardBus slot. Other
application like handheld PC or similar device has not been verified and may not
compliance with related RF exposure rule and such use shall be prohibited.

Operations in the 5.15-5.25GHz band are restricted to indoor usage only IEEE 802.11b
or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1
through 11.

«
...
56
57
58
59
60
...
»

Summary of Contents for AWRT-600N






























































Reviews:

No comments

Related manuals for AWRT-600N

Brand: Panasonic Pages: 20

Brand: Meru Networks Pages: 66

Brand: sauter Pages: 8

Brand: SIYI Pages: 95

Brand: Digisol Pages: 29

Brand: MFOURTEL Pages: 19

Brand: Kraun Pages: 35

Brand: ZyXEL Communications Pages: 144

Brand: ZyXEL Communications Pages: 206

Brand: ZyXEL Communications Pages: 225

Brand: MUNIC Pages: 14

Brand: LYNKSYS Pages: 499

Brand: Marley Pages: 23

Brand: 4IPNET Pages: 15

Brand: 4IPNET Pages: 16

WatchGuard AP327X O-105E

Brand: Watchguard Pages: 32

Brand: iHome Pages: 2

Brand: Allnet Pages: 137

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands