AS ONE NDK-1A-F Instruction Manual Download Page 22

- 21 - 

 

-|Transparent setting guide|-

Specifications

Model

NDK-1A-I

NDK-1A-F

NDK-2A-I

NDK-2A-F

Power supply

220VAC

 50/60Hz

Current consumption

3.1A

4.6A

Heater capacity

680W

1000W

The appearance size (W×L×H) 240×280×90mm

320×360×90mm

The top plate size (W×L)

170×170mm

250×250mm

Material of the top plate

Aluminum (ceramic coating)

Display method

LCD Display

Setting method

Setting by keys and JOG switch at the front body.

Input specifications

Inner 

sensor

Thermocouple: K(CA)

External 

sensor

※1

Thermocouple: K(CA)

Setting range

0.0 to 350.0℃

Display range

-20.0 to 370.0℃

Display accuracy

F.S.±1%

Sampling period

100ms

Control output

TRIAC output

Alarm output

Relay contacts output (max. 12VDC, 50mA)

Communication output

USB communication output

Control method

ON/OFF control, P, PI, PD, PID control

Hysteresis (ON/OFF)

0.1 to 100.0℃

Proportional band width (P)

0.0 to 100.0℃

Integral time (I)

0 to 3600 sec

Derivative time (D)

0 to 3600 sec

Control period (T)

1 to 120 sec

Environment

Ambient temp.

5 to 35℃, storage: -10 to 50℃

Ambient humi.

35 to 85%RH, storage: 35 to 85%RH

Safety device

Fuse

※2

, bimetal switch

Power cable length

Approx. 1.8m

Power plug

IEC type I 

CEE 7/7

※3

 

IEC type I 

CEE 7/7

※3

 

Approval
Weight

※4

Approx. 4.0kg

Approx. 6.5kg

 

※ The above product specifications are subject to change without notice for improvement. 

 

Please kindly understand that.

 

※Environment resistance is rated at no freezing or condensation. 

 

※ This product uses Refractory Ceramic Fiber (RCF) as insulation.

 

It should be done away regarded as industrial waste.

 

※1.  When using an external sensor, a temperature deviation may occur due to the thermocouple's 

resistance value. If a temperature deviation occurs, use the temperature crrection [

AD

function to enter the correction value.

 

Thermocouple K(CA), external sensor, is sold separately. (Model: 1-4601-11)

 

※2. For fuse specifications, see 'product overview' (page 5).

 

※3. CEE 7/7 plug is compatible with IEC type E and type F.

 

※4. The weight excludes packaging.

MADEINJAPAN

Summary of Contents for NDK-1A-F




























Reviews: