background image

12

Aruba 518 Series Ruggedized Access Point

| Installation Guide

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the 

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio or TV technician for help.

Improper termination of access points installed in the United States configured to a non-US model controller is a 

violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a 

requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).

Industry Canada

This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment 
Regulations.

In accordance with Industry Canada regulations, this radio transmitter and receiver may only be used with an 

antenna, the maximum type and gain of which must be approved by Industry Canada. To reduce potential radio 

interference, the type of antenna and its gain shall be chosen so that the equivalent isotropic radiated power 

(EIRP) does not exceed the values necessary for effective communication.

This device complies with Industry Canada's license-exempt RSS regulations. Operation of this device is subject 

to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any 

interference, including interference that may cause undesired operation.

When operated in 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the 

potential for harmful interference with co-channel Mobile Satellite Systems.

This radio transmitter model APIN0518 has been approved by Industry Canada to operate with the antenna 

types listed in the online ordering guide (link provided below) with the maximum permissible gain indicated. 

Antenna types not included in this list, having a greater gain than the maximum gain indicated for that type, are 

strictly prohibited for use with this device.

http://www.arubanetworks.com/assets/og/OG_AP-518Series.pdf

Déclaration d’Industrie Canada

Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce 

périphérique est soumise aux deux conditions suivantes : (1) ce périphérique ne doit pas provoquer 

d’interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles 

de provoquer un dysfonctionnement.

En cas d'utilisation dans la plage de fréquences de 5,15 à 5,25 GHz, cet appareil doit uniquement être utilisé en 

intérieur afin de réduire les risques d'interférence avec les systèmes satellites mobiles partageant le même 

canal.

Ce modèle d'émetteur radio APIN0518 a été approuvé par Industrie Canada pour fonctionner avec les types 

d'antenne énumérés dans le guide de commande en ligne (lien ci-dessous) avec le gain maximal admissible 

indiqué. Les types d'antennes non inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour 

ce type, sont strictement interdits pour une utilisation avec cet appareil.

http://www.arubanetworks.com/assets/og/OG_AP-518Series.pdf

European Union Regulatory Conformance 

The Declaration of Conformity made under Radio Equipment Directive 2014/53/EU is available for viewing at: 

www.hpe.com/eu/certificates

. Select the document that corresponds to your device’s model number as it is 

indicated on the product label.

This radio transmitter model has been approved to operate with the antenna types listed in the online ordering 

guide (link provided below) with the maximum permissible gain indicated. Antenna types not included in this list, 

having a greater gain than the maximum gain indicated for the type, are strictly prohibited for use with this 

device. Compliance is only assured if the Aruba approved accessories as listed in the ordering guide are used.

http://www.arubanetworks.com/assets/og/OG_AP-518Series.pdf

Summary of Contents for 518 Series
















Reviews: