Arturia V76-Pre User Manual Download Page 31 | Manualshive

Page: 31 / 41

background image

5. V76-PRE CONTROL PANEL

The V76-Pre plug-in can be used as a Single Channel (mono) plug-in or as a Double Channel

plug-in. When in Double Channel, we can use it in the traditional Stereo mode (Left/Right)

or the special Mid/Side mode (M/S). We can also use it as a Dual Mono (each of the two

channels works independently).

When in Single Channel configuration, both the preamp and EQ sections have just one

column of controls. The Output section also has just the volume sensor light and the Output

Trim knob.

5.1. Single Channel (Mono)

5.1.1. Single Channel Preamp Section

The Single Channel configuration is automatically loaded when we use the plug-in with

mono channels. The preamp section in the Single Channel configuration is simpler, as are all

the other sections. It is located on the right side of the control panel. The significant elements

start with the Gain control knob at the top.

The original unit had a discrete control, that moved in 6dB steps, but in the Arturia plug-in

version the Input Gain control is continuous, with a range that goes from +3dB up to +76dB.

This is quite an extreme gain range, and although the tube preamp model is extremely

tolerant, it is still possible to create some unpleasant artifacts, nevertheless. At the right

amount, a pleasant saturation is induced. Default value is -3dB (full left).

V76-Pre

Single

Channel

Preamp

gain

control

and

Output

Arturia - User Manual V76-Pre - V76-Pre CONTROL PANEL

27

«
...
29
30
31
32
33
...
»

Summary of Contents for V76-Pre










































Reviews:

No comments

Related manuals for V76-Pre

Brand: Panasonic Pages: 5

Brand: Jam Pages: 7

Brand: NAD Pages: 2

Brand: Meicheng Pages: 23

Brand: Hiwin Pages: 183

Brand: Parasound Pages: 11

Brand: Peavey Pages: 4

Brand: GLEMM Pages: 12

REFERENCE PHONO 10

Brand: Audio Research Pages: 18

Brand: Harman Kardon Pages: 34

Brand: Teac Pages: 28

Brand: Takstar Pages: 7

Velocity VD 1002

Brand: Blaupunkt Pages: 22

Brand: GLX Pages: 2

Brand: Toa Pages: 2

Brand: B&K Pages: 16

Brand: VOX Amplification Pages: 69

CAD 300 SE Signature

Brand: Cary Audio Design Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands