![background image](http://html1.mh-extra.com/html/artsound/art3-1bt/art3-1bt_user-manual_2978880003.webp)
3
ART3.1
1
2
3 4
5
1.
voeding, 230 AC / alimentation, 230 CA / power, 230 AC
2.
aansluiting luidsprekers / connexion des enceintes / speaker connection
3.
FM antenne / Antenne FM / FM antenna
4.
BT antenne / Antenne BT / BT antenna
5.
setup knop / bouton setup / set-up button
.
Mono/Stereo switch / commutateur mono/stéréo / Mono/Stereo switch
.
3,5 mm stereo input / entrée stéréo 3,5 mm / 3.5 mm stereo input
1
2
Pair
3
4
5
6
FM
DAB
BT
ON
OFF
HI
AUX
LO
+
>>
>>
—
INSTALLATION
To install correctly follow the steps listed below.
1. Positioning
The device has 4 feet so that it can be freely positioned. In addition it has a
DIN-rail-compatible notch, so that the module can be fixed onto a rail.
2. Connection to an external audio source
Any kind of analogue audio source can be connected via the 3.5 mm stereo input.
3. Connecting the loudspeakers
2 loudspeakers can be connected to the ART3.1BT. Remember that the polarity of
the loudspeaker must correspond to what is indicated on the screw connection on
the ART3.1BT. The loudspeaker should be type 4 or 8 ohm.
4. FM aerial
You can use the FM aerial supplied. Plug this into the connector intended.
5. BT antenne
Screw the BT antenna to the connector supplied for this purpose in order to gene-
rate the very best Bluetooth reception.
CONFIGURATION
First, make sure both speakers are connected; alternatively, connect an active
audio source to the AUX input (RCA cable).
1. Programming the remote control address
• Press AUX until the RF LED lights up continuously.
• Make a 3-digit combination on the numeric keypad on the remote control. (111
to 666).
• Press briefly AUX to save the combination.
• Repeat the aforementioned procedure if necessary to connect up to 10 con-
trols with different addresses.
2. Connecting to the ART3.1BT
• Press and hold the set-up button on the unit for 5 seconds until the RF LED
starts to flash.
• Press OFF on the remote control. The LED will flash during the scanning
process.
3. Mono/Stereo
Put the mono/stereo switch in the mono setting if:
• only one speaker is connected,
• several speakers are positioned at a distance away from each other,
• several speakers are distributed in 2 or more rooms.
4. DAB sets
Press and hold down DAB once only to programme the DAB sets. You will hear an
audio signal during the programming. Afterwards you can search in the same way
as for FM via << and >>.
r
When using more than one ART3.1BT unit in the same project you must
programme different addresses to avoid interference.
USE
1. Choice of source
Using the FM, DAB, AUX or BT keys, one of these sources can be selected.
2. Bluetooth
For BT, a compatible device first needs to be connected via the PAIR key. Press
briefly on << or >> to select the previous or next track, press for longer on << or >>
to go backward or forward in the song.
While selecting another source the current song will be stopped.
3. Saving preset channels / tone control
After a manual search, preset channels can be saved by pressing a numeric key on
the remote control for 2 seconds.
Press briefly on << or >> to select the previous of the next preset, press for longer
on << or >> to scan the waveband. By pressing the HI/LO keys and +/- respec-
tively, a higher/lower tone can be programmed. Pressing on the HI or LO key for
longer will restore the settings to their default value.
UK