background image

 

4

 

 

Always power off/unplug the fixture before removing any covers. 

 

Ensure that the power is turned off when connecting the fixture to the AC 

mains supply. 

 

Ensure that the fixture is electrically connected to earth (ground). 

 

Do not apply power if the fixture is in any way damaged. 

 

Do not immerse the fixture in water or liquid. 

   

Preventing burns and fire 

 

 

 

Install in a location that prevents accidental contact with the fixture. 

 

Install only in a well-ventilated space. 

 

Install at least 0.3 m (12 in.) away from objects to be illuminated. 

 

Install only in accordance with applicable building codes. 

 

Ensure a minimum clearance of 0.1 m (4 in.) around the cooling fans. 

 

Do not paint, cover or modify the fixture. 

 

Keep all flammable materials away from the fixture. 

 

Allow the fixture to cool for 15 minutes after operation, before touching it. 

 

CAUTION:  Exterior  surface  temperature  after  5  min.  operation  =  45  °C 

(113 °F). Steady state = 60 °C (140 °F). 

   

Avoid personal injury 

 

WARNING! 

Take measures to prevent burns and fire.

 

WARNING! 

Risk of electric shock.

 

 

13

10-50 

Dimmer curve 1 

51-101 

Dimmer curve 2 

102-152 

Dimmer curve 3 

153-203 

Dimmer curve 4 

204-249 

Dimmer curve 5 

250-255 

Dimmer curve 6 

10 

0-255 

Color temperature (Warm to Cool) 

 

12.

 

Control menu 

 

 

Display:

 

 

MENU 

To select the programming functions 

DOWN 

To go backward in the selected functions 

UP 

To go forward in the selected functions 

ENTER 

To confirm the selected functions 

 

Set    DMX Address Code 

1.

 

Press "

Menu

" to "Set DMX Address",and press "

ENTER

" keys to enter into 

2.

 

Show "Set DMX Address DMX Address:001",Press the "

UP

 and 

DOWN

keys to amended 

3

 

Press "

ENTER

" keys to save and Exit,Press the "

MENU

" Keys does not 

save and Exit

 

Summary of Contents for IP WASH 44









Reviews: