background image

Care and Maintenance

Recycle: The Battery provided in this product should be recycled to protect the local environment. 

Please contact with local recycle department for detail.

FCC Certifications

Federal Communication Commission Interference Statement

This equipment has been tested and improved to comply with the limits of a Class B digital device, pursuant to 

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses and can radiate radio frequency 

energy, if installed and used not in accordance with the instructions, may cause harmful interference to radio 

communications. However,there is no guarantee that interference will not occur in a particular installation. If this 

equipment does cause harmful interference to radio or television reception, which can be determined by turning 

the equipment off and on, the user is encouraged to try to correct the interference by one of the following 

measures:

 

Reorient or relocate the receiving antenna.

 

Increase the separation between the equipment and receiver.

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

(1)This device may not cause harmful interference, and (2)this device must accept an interference received, 

including interference that may cause undesired operation.

FCC Caution: Any changes or modifications are not expressly approved by the party responsible for 

compliance which could void the user's authority to operate this equipment.

FCC ID Master: WMPM06A01

Slave: WMPS05A01

EU Declaration Conformity

This product is carrying the CE-Mark in accordance with the related European Directives.

(e)  The working range, alarm range, searching and detection are depends the terrain environment because 

of radio wave efficiency.

(f)  If the beeps sound are not loud enough, it may means the battery low. Change new battery for louder 

alarm sound.

(g)  If you want to apply this product during the flight trip, please comply with the flight safety law according to 

each country.

2

Summary of Contents for Mini Tracker 506




















Reviews: