background image

11 

SPECIFICATIONS 

Input Connections 

 

XLR, 1/4” TRS, balanced 

Output Connections 

 

XLR, 1/4” TRS, balanced 

Frequency Response 

 

10Hz to 20kHz, +0/-1.5dB 

Crossover Frequency Range 

x1 

 

80Hz to 920Hz 

x10 

 

800Hz to 9.2kHz 

Crossover Filter Type 

 

Fourth-order Linkwitz-Riley, 24dB/octave 

Dynamic Range 

 

118dB 

Signal to Noise Ratio 

 

>85dB  

Input Impedance  

 

20k Ohms 

Output Impedance  

 

150 Ohms 

Maximum Input Level 

 

+13dBu 

Maximum Output Level 

 

+21dBu 

Total Harmonic Distortion (THD)   

<0.05% (20Hz-20kHz) 

Maximum Gain 

 

+4dB 

Power Requirements 

 

105-120V AC, 50-60hz, 3VA (USA) 

 

 

Export units configured for country of destination 

Dimensions (HWD) 

 

1.75” x 19” x 6.5” 

 

 

44mm x 483mm x 165mm 

Weight 

 

7.1 lbs. (3.2 kg) 

ART maintains a policy of constant product improvement. ART reserves the right to make changes in 

design or make additions or improvements to this product without any obligation to install these 

changes on products previously manufactured. Therefore, specifications are subject to change 

without notice. 

Summary of Contents for CX310













Reviews:

Related manuals for CX310