background image

Page 6 · 274 

TECMount

 User’s Manual  

 

 

Technical Specifications 

 

 

274 TECMount 

 

COLD PLATE 

 

Mounting Holes 

M3 

 

 

TEMPERATURE CONTROL 

 

Standard Model (+85

°

C) 

 

Temperature Range (°C) 

-25 to +85, non-condensing 

Sensor Type 

10k

 Thermistor 

High Temp Model (+150

°

C) 

 

Temperature Range (°C) 

-25 to +150, non-condensing 

Sensor Type 

100

 Platinum RTD 

TE Module (at 25°C)

1

 

Imax = 16A 

 

Vmax = 33V 

CONNECTORS / INTERFACES 

 

Temperature Controller 

DB-15, male 

External Sensor 

Phoenix 2-Pin (plug p/n 1803578) 

Coolant Inlet/Outlet 

1/8” Female NPT with pre-installed 
brass hose barbs (3/8” I.D. hose) 

 

 

GENERAL 

 

Recommended Coolant 

Distilled Water 

Max Water Pressure (psi) 

80 

Max Housing Temperature (°C) 

60 

Size 

(H x W x D) [in(mm)]

 

2.5 (63.5) x 4.8 (121.9) x 3.2 (81.3)  

 

Wetted Materials 

 

 
For purposes of evaluating galvanic corrosion, the following materials will make 

contact with the coolant: 
 

 

Housing: Anodized AL 6061-T6 

 

Dissipative plate:  Electroless nickel plated AL 6061-T6 

 

Fittings: UNS C36000 Brass 

 

O-ring: EPDM 

 

 

                                                 

1

 See 

Operating at High Temperatures

, below, for additional requirements at high temperatures

 

Summary of Contents for TECMount 274





















Reviews: