background image

* Size rounded off to the nearest foot

BUILDING DIMENSIONS

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES
TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ
SAFETY INFORMATION PROVIDED IN THIS MANUAL
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
WHEN HANDLING METAL PARTS.

711251207

Model No.

 ED106

GD106-B
GDF106-A

Owner's Manual & Assembly Instructions

       PN01

                                                                       Exterior Dimensions             Interior Dimensions             Door

       *Approx.       Foundation        Storage Area           (Roof Edge to Roof Edge)              (Wall to Wall)               Opening
           Size               Size             Sq. Ft.  Cu. Ft.        Width      Depth      Height      Width     Depth    Height   Width  Height

         10' x 6'     121" x 68 3/4"           54        345         123 1/4"    71 1/4"     82 1/8"     118 1/4"       66"      80 7/8"  55 1/2" 69 1/4"

3,0m x 1,7m  307cm x 175cm        5,0m

2

     9,8m

3

        313cm       181cm       209cm        300cm      168cm     205cm    141cm   176cm

Summary of Contents for ED106

































Reviews: