Arrow ED106 Owner'S Manual & Assembly Instructions Download

Page: 22 / 32

Each screw in the wall requires a
washer.

Slide

side siding

into channels

of corner posts, flat edge upward,
bottom edge down resting on floor
frame. Always follow this pattern.
Fasten bottom edge and tab of stud to
floor frame using screws. Fasten
center to stud with screws. Do not
fasten flat edge yet.

Install

side siding

as before. Note

how the slot in bottom edge must
overlap flat edge of last siding.
Fasten both siding panels to stud at
this overlap.

Install

side siding

to the top as

before.

From inside building, fasten siding

to corner posts using screws.

Repeat steps 1 through 4 for oppo-

site side of building.

NOTE

Be careful to install the correct

panel in each position as shown.

The floor frame must be square

and level or holes will not align.

●

8719 Side Siding (6)

●

Parts Needed For

●

Side Siding

Step 9

X22

THIS SCREW MUST

FASTEN TAB OF STUD

STEP

Be certain all Siding

overlaps are fastened

with a single screw

Washer

8719

End

View

Flat

Edge

Bottom

Edge

FRONT

STEP

Summary of Contents for ED106

































Search results

Summary of Contents for ED106

Reviews:

Related manuals for ED106

Brands by name

Popular brands

Arrow ED106, Owner'S Manual & Assembly Instructions

Search results

Summary of Contents for ED106

Reviews:

Related manuals for ED106

Brands by name

Popular brands