Arrow ED1012 B1 Owner'S Manual & Assembly Instructions Download

Page: 31 / 36

Install the second ridge cap 6868

overlapping the fi rst ridge cap while

installing two roof panels 6529. Hint:

The bolts on the ridge cap need to

be left loose to move the ridge cap

to the side and overlap the ribs of the

next roof panel. Continue weather

stripping the ridge.

Install the third ridge cap 6869

overlapping the second ridge cap

while installing the remaining two

roof panels 6529. Hint: The bolts

on the ridge cap need to be left loose

to move the ridge cap to the side and

overlap the ribs of the next roof panel.

Continue weather stripping the ridge.

Install the left 6641 and right roof

panel 6640 as you unroll the weather

stripping tape, and press it down.

Fasten the lower end of the panels

to the side wall angles using screws

and washers.

Fasten the roof panel ribs, peak

cap and ridge cap together using

bolts and nuts.

6868 Ridge Cap (1)

6529 Roof Panel (4)

6869 Ridge Cap (1)

6641 Left Roof Panel (1)

6640 Right Roof Panel (1)

Step 18

SX31 ctr

Parts Needed For

Ridge Cap & Panels

Weather

Stripping Tape

STEP

6868

6529 Roof Panel

6529

Roof Panel

6869

6529

6640

6641

6529

Peak Cap

Cut Weather Stripping

and Fold Under

STEP

(88)

(24)

Summary of Contents for ED1012 B1





































Search results

Summary of Contents for ED1012 B1

Reviews:

Related manuals for ED1012 B1

Brands by name

Popular brands

Arrow ED1012 B1, Owner'S Manual & Assembly Instructions

Search results

Summary of Contents for ED1012 B1

Reviews:

Related manuals for ED1012 B1

Brands by name

Popular brands