Arrow ED1012 B1 Owner'S Manual & Assembly Instructions Download

Page: 30 / 36

Install a left roof panel 6641 at

the left rear corner of the roof.

Cover the joint at the peak with

weather stripping tape. Unroll the

tape and press it down over the

opening at the ridge as you install

each roof panel. Do not cut the tape

at this time.

Install two roof panels 6529 work-

ing side to side. Do not fasten the

lower end of the panels to the side

wall angles at this time. Continue

weather stripping the ridge opening.

NOTE

Narrow roof panel crimped rib is

overlapped by wide rib of

adjacent panel where possible

Install the fi rst ridge cap 6869 on

the completed roof section using bolts

and nuts. Do not fasten the ends of

the ridge cap at this time.

Fasten the roof panel ribs, peak

cap and ridge cap together using

bolts and nuts.

6641 Left Roof Panel (1)

6529 Roof Panel (2)

6869 Ridge Cap (1)

Step 17

SX30 ctr

Parts Needed For

Ridge Cap & Panels

STEP

Screws To

Roof Beam

Screws To

Roof Beam

STEP

Weather

Stripping

Tape

Do not fasten

at this time

6529

Roof

Panel

STEP

6529

6641 Left

Roof Panel

6869

Fasten At

Overlap

With Bolt

Fasten At

Overlap

With Bolt

NOTE

If roof beam holes do not line up with

the roof panel holes, shift the building

from left to right. If this does not help,

your building may not be level. Shim

the corners until holes line up.

(24)

(11)

Summary of Contents for ED1012 B1





































Search results

Summary of Contents for ED1012 B1

Reviews:

Related manuals for ED1012 B1

Brands by name

Popular brands

Arrow ED1012 B1, Owner'S Manual & Assembly Instructions

Search results

Summary of Contents for ED1012 B1

Reviews:

Related manuals for ED1012 B1

Brands by name

Popular brands