background image

Owner's Manual

Before beginning construction, check local building codes regarding footings, location 

and other requirements. Study and understand this owner's manual.

Important information and helpful tips will make your construction easier and more 

enjoyable.

Assembly Instructions:

 Instructions are supplied in this manual and contain all 

appropriate information for your building model. Review all instructions before you begin, 

and during assembly, follow the step sequence carefully for successful results.

Flooring and Anchoring:

 Your storage building must be anchored to prevent wind 

damage. A base is necessary to construct a square and level building. Anchoring and 

base materials are not included with your building. We recommend the combined use 

of an Arrow Floor Frame Kit and an Arrow Anchoring Kit as an effective method of 

securing your building to the ground (Available at your local dealer, Arrow's website 

arrowsheds.com or call Arrow's Customer Service department 1-800-851-1085) or you 

may construct a base and anchoring system of your choice. Your assembly instructions 

provide information on a few methods commonly used to secure and level a storage 

building.

Parts and Parts List:

 Check to be sure that you have all the necessary parts for 

your building.

 

•All part numbers can be found on the parts. All of these numbers (before the -) must agree with the 

 

numbers on the Parts List page.

 

•If you fi nd that a part is missing, include the model number of your building and contact: 

 

Arrow Shed, LLC               Customer Service Department  

 

1101 North 4th Street      Breese, Illinois 62230

 

 

 

•Separate contents of the carton by the part number while reviewing parts list.  The fi rst few steps 

 

show how to join related parts to make larger sub assemblies which will be used later.

 

•Familiarize yourself with the hardware and fasteners for easier use during construction. These are

 

packaged within the carton. Note that extra fasteners have been supplied for your convenience.

 

BEFORE YOU BEGIN....

    A03

1-800-851-1085   or   [email protected] 

Summary of Contents for PT104





























Reviews: