background image

* Size rounded off to the nearest foot

BUILDING DIMENSIONS

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE

MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES

TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ

SAFETY INFORMATION PROVIDED IN THIS MANUAL

BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES

WHEN HANDLING METAL PARTS.

716440616

Model No.       EPA84

Owner's Manual & Assembly Instructions

           YL01

Storage Area:  28 Sq. Ft.       150 Cu. Ft.

  

 2,6 m

2

   

4,2 m

3

 

                                             Exterior Dimensions                     Interior Dimensions                    Door

       *Approx.              Base                      (Roof Edge to Roof Edge)                      (Wall to Wall)                      Opening

           Size                  Size                    Width       Depth       Height           Width       Depth      Height       Width     Height      

 

          8' x 4'       97 1/2" x 45 1/4"            100"            47"        67 3/4"           94 3/4"     42 1/2"     66 9/16"      43 1/2"       60"       

2,4 m x 1,1 m   247,7 cm x 114,9 cm       254,0 cm      119,4 cm     172,1 cm          240,7 cm    108,0 cm     169,1 cm      110,5 cm    152,4 cm

 

Summary of Contents for EPA84





























Reviews: