Arrow Storage Products BD88GB Owner'S Manual & Assembly Instructions Download Page 28

Page: 28 / 32

Step 15

BY28



Parts Needed For



Ridge Caps & Panels



8840 Ridge Cap (1)



9978 Roof Panel (2)



8486 Ridge Cap (1)

Install the ﬁ rst

ridge cap

on the

completed roof section using bolts

and nuts. Fasten roof panel over-

laps not used for ridge cap. Cover

the head of bolt with the 2" (5,1 cm)

piece of weather stripping tape. Do

not fasten the ends of the ridge cap

at this time.

Install the second

ridge cap

overlapping the ﬁ rst ridge cap while

installing the remaining narrow

roof

panels

. Continue weather stripping

the ridge.

Fasten the lower end of the panels

to the side wall angles using screws

and washers. Use bolts and nuts

through wall angle overlaps at the

bottom of the panel.

STEP

8840

Strips

STEP

9978

8486

Cut Weather

Stripping and

Fold Under

9978

STEP

Summary of Contents for BD88GB

































Search results

Summary of Contents for BD88GB

Reviews:

Related manuals for BD88GB

Brands by name

Popular brands

Arrow Storage Products BD88GB, Owner'S Manual & Assembly Instructions

Search results

Summary of Contents for BD88GB

Reviews:

Related manuals for BD88GB

Brands by name

Popular brands