ARRI WRC-1 Instruction Manual Download Page 12 | Manualshive

Page: 12 / 196

background image

12

3.2 Functions

The WRC/CAM sliding switch is used to select
the operating mode

➪

photo

.

3.2.1 CAM mode

In CAM mode, the operator can access the same settings
and modes that are directly available on the camera itself.
The display on the WRC-1 shows the same information as
the camera display.

The MODE, SEL, SET and RAMP buttons have the same
functions as their respective counterparts on the camera.
A RUN LED is also integrated.

In the CAM mode, the OPEN button on the WRC-1 serves
as the PHASE button on the camera.

In CAM mode the WRC-1 serves purely as a camera
remote control unit, without any wider programming options.
The handwheel, the WRC and the COMPENSATION
rotary switches are without function in this operating mode.

WRC/CAM sliding switch

WRC

rotary switch

COMPENSATION

rotary switch

IRIS sliding switch

SET button

RAMP button

SEL button

MODE button

OPEN/PHASE-

button

handwheel

Functions

«
...
10
11
12
13
14
...
»

Summary of Contents for WRC-1





































































































































































































Reviews:

No comments

Related manuals for WRC-1

Brand: Parasound Pages: 72

Brand: Jafar Pages: 15

Brand: Datavideo Pages: 8

Brand: FAAC Pages: 32

Brand: V2 ELETTRONICA Pages: 72

Brand: jablotron Pages: 22

Brand: jablotron Pages: 2

Brand: WAREMA Pages: 112

Brand: WAGO Pages: 414

Brand: V2 Pages: 48

Brand: Zennio Pages: 30

Brand: Zeta Pages: 13

Brand: CAME Pages: 2

Brand: ISVT Pages: 78

Brand: Linear Technology Pages: 8

Brand: Precision Pages: 8

TRAP-SHUFFLE Game Simulator

Brand: RF SOLUTIONS Pages: 2

Brand: DNF Controls Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands