manualshive.com logo in svg

ARRI WRC-1, Instruction Manual

Share
Download
ARRI WRC-1 Instruction Manual Download Page 174

174

7.3.1 Iris control

• Before using the iris control functions, the T-stops

engraved on the lens being used must be assigned in
the WRC-1 and the lens’ end-stops must be calibrated.
If a lens has not yet been selected and assigned to the
T-stop values in the WRC-1 (condition on delivery from
the factory, or the active iris table has been deleted
from the memory), a flashing warning ‘IRIS TBL’
appears when the WRC-1 is switched on with the IRIS
sliding switch set to the position ‘IRIS ON’.
Press the MODE button to switch to the input mode.
If a lens has already been selected and programmed,
the menu for selecting lenses or assigning T-stops can
be accessed in the WRC rotary switch position ‘IRIS’.
The so called table menu is the last submenu before
returning to the main menu.

• Press the MODE button three times in the main menu

in the WRC rotary switch position ‘IRIS’ with the
COMPENSATION rotary switch at ‘OFF’ until ‘TBL
LOAD’ is shown on the display.

user defined

factory pre-defined

Quick Guide

Summary of Contents for WRC-1





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands