ARRI UMC-4 User Manual Download Page 44

Page: 44 / 54

Page 44 of 54

Universal Motor Controller UMC-4

– User Manual – V 02/2015

K2.0002855

Cable UMC-4 to EPIC (additional RS IN cable required)

K2.65235.0

Cable UMC-3/4 to Video-RS/PSC (additional PSC cable
required)

K2.65012.0

Cable UMC-3/4 to Cooke/i (supported with UMC-4 SUP
1.1)

K2.65063.0

Cable UMC-3/4 to Cine Tape Measure (coiled)

K2.0003252

Cable TC IN/OUT (Ambient)

K2.0003254

Cable TC OUT BNC (Ambient)

K2.0003253

Cable TC IN BNC (Ambient)

K2.0003255

Cable TC OUT for EPIC (Ambient)

K2.0002043

UMC-4 connector module to Fujifilm focus/zoom demands
FUJ-1

K2.0002042

UMC-4 connector module to Canon focus/zoom demands
CAN-1

K2.0002046

UMC-4 connector module with two serial connectors
(supplied with UMC-4)

Compatible Products

The UMC-4 supports the following products:

•

Wireless Compact Unit WCU-4

•

Single Axis Unit SXU-1

•

Zoom Main Unit ZMU-3A

•

Wireless Zoom Extension WZE-3

•

Wireless Compact Unit WCU-3

•

Wireless Main Unit WMU-3

•

Wireless Focus Unit WFU-3

Summary of Contents for UMC-4























































Search results

Summary of Contents for UMC-4

Reviews:

ARRI UMC-4, User Manual, Page: 44 / 54

Search results

Summary of Contents for UMC-4

Reviews: