manualshive.com logo in svg

ARRI UMC-4, User Manual, Page: 3 / 54

Share
Download
ARRI UMC-4 User Manual Download Page 3

 

 
Universal Motor Controller UMC-4

 – User Manual – V 02/2015 

Page 3 of 54 

Imprint 

Copyright © 2014 Arnold & Richter Cine Technik GmbH & Co. Betriebs KG. 
All rights reserved. No portions of this document may be reproduced 
without prior written consent of Arnold & Richter Cine Technik GmbH & Co. 
Betriebs KG. Specifications are subject to change without notice. Errors, 
ommissions, and modifications excepted. ARRI, ALEXA, LDS and LENS 
DATA SYSTEM are trademarks or registered trademarks of Arnold & 
Richter Cine Technik GmbH & Co. Betriebs KG. All other brands or 
products are trademarks or registered trademarks of their respective 
holders and should be treated as such. Original version. 

 

For further assistance: 

ARRI Cine + Video Geräte Gesellschaft m.b.H. 

Pottendorferstraße 25-27/3/1 

A-1120 Vienna 

Austria 

E-mail: [email protected] 

www.arri.com 

 
Scope 

This instruction manual applies to the following product: Universal Motor 
Controller UMC-4 with Software Update Package (SUP) 1.1 

Document Information 

Version

 

Document No.

 

Date

 

01 

K5.0003467 

28.08.2014 

02 

K5.0003467 

09.02.2015 

 

 

Summary of Contents for UMC-4























































Reviews:

No comments