manualshive.com logo in svg

ARRI UMC-4, User Manual, Page: 36 / 54

Share
Download
ARRI UMC-4 User Manual Download Page 36

 

 

Page 36 of 54 

Universal Motor Controller UMC-4

 – User Manual – V 02/2015 

6.  The UMC-4 will reboot after the update is completed. Depending 

on the update package content, additional modules might need to 
be updated after reboot; this is done automatically and is clearly 
indicated on the screen of the device. The second phase of the 
update procedure may take several minutes. 

 

Do not switch power off and do not remove the SD card during 
the update as this may damage the UMC-4! In case of problems, 
see the troubleshooting section. 

 

Save Log to SD Card Menu 
Select the 

Save Log to SD Card

 menu if you want to save the log file to the 

SD card. This may be required when you contact the ARRI support staff. 
The log file will be saved immediately and can be found in the 
/ARRI/UMC4/logs directory. 

Format SD Card 
Select 

Format SD Card 

to format the SD card and add the ARRI specific 

directory structure: 
/ARRI/UMC4  /Firmware 
 

          /Logs 

                       /Metadata 
 

 

/Settings 

 
Note: All the data on the SD card will be lost after formatting the card! 
 

System Info Menu 
Select the 

System Info 

menu to identify the current firmware version, the 

serial number, and the power source’s current voltage. 
 

Summary of Contents for UMC-4























































Reviews:

No comments