background image

22

Appendix

K2.0007318

Cable LBUS to LCS 0,8m/2.5ft

K2.0006757

Cable LBUS to D-Tap 1.2m/4ft LPS-7-01

K2.0006758

Cable LBUS to D-Tap 0.8m/2.5ft LPS-7

K2.0006759

Cable LBUS to RS 0.8m/2.5ft LPS-1

K2.0006760

Cable LBUS to XLR-4 0.8m/2.5ft LPS-6

DANGER!

Risk of fire!

Short-circuits and back currents to power supplies/batteries may

entail lethal damage!
Always use original ARRI/cmotion LBUS cables to external

power sources (D-Tap, XLR)! ARRI/cmotion LBUS cables to

external power sources provide a protection circuit to prevent

back currents to power supplies/batteries.

Gears for cforce plus Lens Motor

K2.0009335

cforce plus gear assembly with module 0.8, 60

teeth

K2.0010365

cforce plus gear assembly with module 0.8, 60

teeth, 25 mm extra-wide

K2.72111.0

gear assembly with module 0.6, 70 teeth

K2.0002044

gear assembly with 48 pitch, 75 teeth

K2.72110.0

gear assembly with module 0.5, 80 teeth

K2.72109.0

gear assembly with module 0.4, 100 teeth

K2.0000244

gear flange

K2.72127.0

knurled head captive screw

K2.72116.0

gear set module 0.8, 0.6, 0.5, 0.4

Note: You need a Torx key #6 to swap gear

flange between gears

Summary of Contents for cforce plus





























Reviews: