background image

For all Sales and Service enquiries  
Phone (03) 9727 8860  Fax 1300 350 650

CPIN104/3

Sales and Service enquiries in New Zealand and the 
South Pacific contact PDL Industries Ltd.

New Zealand: 

Phone 0800 735 746 

Fax 0800 863 297

Fiji: 

Phone +679 323 5344 

Fax +679 397 973

Papua New Guinea: 

Phone +675 323 5344 

Fax +675 323 5340

All other South Pacific:  Phone +64 3 339 1887  Fax +64 3 339 1672

© This instruction leaflet is subject to copyright and must not be reproduced,
copied or otherwise used in any way or for any purpose without the consent
in writing of the owner, Arlec Australia limited (A.C.N. 003 118 787).

Arlec Guarantee

Arlec guarantees this product against defects of materials
and workmanship for a period of 1 year from the date of
purchase provided that the product is used in accordance
with Arlec’s recommendations and within such voltage and
current limits as are specified by Arlec in relation to the
product. Arlec will at its own option make good, replace
with the same or similar product, or provide credit for any
product manufactured or supplied by it, which proves to be
defective within the limits set out above provided that no
repairs, alterations or modifications to the product have
been undertaken or attempted, other than by the company
or its authorised agents. Should the purchaser wish to make
a claim under the guarantee, the product should be
returned pre-paid to the place of purchase. This guarantee
is in addition to and does not take away from any rights
available to the consumer under the Trade Practices Act
and the State consumer protection legislation.

Proof of Purchase

Please retain your purchase receipt for all 
warranty claims.

Summary of Contents for MAL413







Reviews: