Arjohuntleigh Minuet 100500AUS User Manual Download

Page: 12 / 16

12 AH-MIN V3

/17

3. Tactile inspection of the buttons:

All buttons should be operated and response tested.

Depress each button on the handset. Each button should have a positive audible click that is

also felt. The function being pressed should also operate.

If the button:



does not have a click feel



does not have an audible click sound



does not immediately operate the function



feels soft offering no resistance



feels different to the rest of the buttons



travels further when depressed

Immediately quarantine the bed and report the damage to maintenance staff

or replace the Handset, otherwise contact an ArjoHuntleigh approved Technician.

The following table identifies some fault symptoms, their possible cause and

suggest some simple checks and corrective actions. If these actions fail to

solve the problem consult the ArjoHuntleigh Service Department on Freecall

1800 072 040.

Symptom

Possible Cause

Action

Actuators fail to work

Power disconnected or

batteries discharged

(battery backup models

only)

Ensure mains supply lead is

connected

Handset disconnected

Check the handset plug is

fully inserted in the control

box

Blown fuse

Contact ArjoHuntleigh

Service Department on

1800 072 040

Damaged handset cable Replace handset

One actuator does not work Actuator plug

disconnected

Check the actuator plug us

fully inserted in control box.

Summary of Contents for Minuet 100500AUS

















Search results

Summary of Contents for Minuet 100500AUS

Reviews:

Related manuals for Minuet 100500AUS

Brands by name

Popular brands

Arjohuntleigh Minuet 100500AUS, User Manual

Search results

Summary of Contents for Minuet 100500AUS

Reviews:

Related manuals for Minuet 100500AUS

Brands by name

Popular brands