manualshive.com logo in svg

Arjohuntleigh Malibu, Instructions For Use Manual, Page: 31 / 60

Share
Download
Arjohuntleigh Malibu Instructions For Use Manual Download Page 31

31

Microbiological Formation Prevention

In order to enhance the on-site curative actions 
(chlorine or thermal shock), which do not guarantee 
a reduction of the contamination long term, make 
sure to follow the instructions below.

      

Do not forget to contact ArjoHuntleigh for the annual 
Preventive Maintenance visit.

Replace Disinfectant Bottle 

(7 steps)

1 Put on protective gloves and glasses.
2 If the disinfectant bottle is empty do as follows: 

•  open the bottle cap, 
•  disconnect the disinfection suction part from 

the bottle,

•  discard the old bottle and replace with a new 

one and

•  attach the suction part on the bottle opening.

3 Set the temperature control as low as possible.
4 Grab the disinfection spray handle.
5 Spray disinfectant while keeping an eye on the 

flow meter.

6 Check the liquid value so it is in accordance with 

the recommended mix ratio according to section 

Disinfection Unit on page 17

.

      

      

7 Make sure to close the disinfection cover after 

use, to prevent the patient getting their feet hurt 
during lowering of the chair. 

Installation precautions

In order to limit the growth of bacterial flora, it is 
necessary to take action at four levels:

•

Avoid stagnating water and make sure proper 
water circulation;

•

Take precautions against the formation of scale 
and corrosion based on the water quality;

•

Maintain a high water temperature all the way 
from the hot water dispenser to the different 
distribution pipes; 

•

Mix hot and cold water as close as possible to the 
point of use.

Use

•

Make sure that the water circulates in the bath 
and the shower on a daily basis 

even if the 

bathtub is not used

; and particular to make sure 

to remove any water that may be left behind in 
the hose.

•

Let the water flow approximately 5 minutes 
before the first bath of the day.

•

Clean and disinfect the bathtub according to the 

IFU

 before the first bath of the day and after the 

bath of each patient.

WARNING

To prevent cross-contamination, always 
follow the disinfection instructions in this 

Instructions for Use.

Arjo Clean

 (50)

Summary of Contents for Malibu





























































Reviews:

No comments