background image

How to Use the KWIKtrak Turntable

10

001.1

1720.EN rev

. 13

Automatic KWIKtrak Turntable

Operating the Turntable

1) Make sure the lift is powered.
2) Move the lift into the turntable and release the

button on the hand control. Wait for the beep

sounds.  The  turntable  will  rotate  to  the  next

position.

3) Move the lift out of the turntable along the new

path.

4) If the turntable fails to operate automatically or

in an emergency situation, manually rotate the

turntable  after  sliding  and  holding  the  quick-

release  button  in  the  open  position

(see Fig. 4). Take care for not getting injured.

Fig. 4

Manual KWIKtrak Turntable

Operating The Turntable

1) Move the lift into the center of the turntable.

2) Make  sure  that  the  lift  is  centered  with  the

turntable,  then  pull  the  Turntable’s  shortest

cord until the pivoting track is aligned with the

next position.

3) Move the lift out of the turntable along the new

path.

4) In  case  of  a  malfunction,  pull  down  the

activation arm, to unlock the pivoting track, and

rotate  the  track  manually.  Take  care  for  not

getting injured.

Adjusting Pull Cord’s Length

If the pull cords are too long, they may be 

shortened as follows.
1) Turn  the  mechanism  halfway  so  that  both

cords are of equal length.

2) Cut  both  cords  to  equal  length  making  sure

that  you  leave  at  least  20 cm  (8  in) on  each

cord.

3) Insert  one  knob  on  each  cord  and  secure  it

with a double knot.

Fig. 5

CAUTION: 

Pay  attention  to  pull  cords,  when

moving  the  ceiling  lift  onto  or  out  of  the

turntable,  to  make  sure  they  do  not  get

entangled. 

Note: 

The mechanism may block if the ceiling

lift  is  not  centered  under  the Turntable  before

pulling the cords.

Shortest possible length

͑͑͑

 20 cm

Can be cut anywhere 

within this range

Cut both cords equal

when Turntable is

turned halfway

How to Use the KWIKtrak Turntable

Summary of Contents for KWIKtrack





















Reviews: