Ariston AURES S 3.5 COM PL, Manual

Page: 4 / 88

4
EN
TECHNICAL CHARACTERISTICS
For the technical specifications, refer to the nameplate (the nameplate is located on the right side of the
water heater).
PRODUCT INFORMATION
Model AURES Model AURES
S 3.5 COM PL S 3.5 COM PL
S 3.5 SH PL S 3.5 SH PL
S 3.5 COM EU S 3.5 COM EU
S 3.5 SH EU S 3.5 SH EU
S 4 SH EU S 4 SH EU S 5 SH EU S 5 SH EU
S 5.5 SH EU S 5.5 SH EU
SF 5.5 COM EU SF 5.5 COM EU
SF 7 SH EU SF 7 SH EU S 7.7 SH EU S 7.7 SH EU
Power 3.5kW 3.5-4.1kW 4-4.7 kW 5-6 kW 5.5-6.5KW 7-8.3kW 7.7-9.1kW
Voltage 220 220-240 220-240 220-240 220-240 220-240 220-240
Phases Mono Mono Mono Mono Mono Mono Mono
Installation Over sink
Construction Open Outlet
Model Refer to name plate
Frequency 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz
Electric current 15.9 A 17.1 A 19.6 A 25 A 27.1 A 34.6 A 37.9 A
Water Protection IP25
Pipe Connection 1/2" BSP
Minimum Water
Pressure
20 kPa (0.2 bar)
Qelec (kwh) 2.119 2.119 2.119 2.119 2.119 2.224 2.224
Load Profile XXS XXS XXS XXS XXS XS XS
Lwa (dB) 15 dB
η
wh 40% 38%
Rated Volume (l) 0,35 l 0,35 l 0,35 l 0,35 l 0,35 l 0,35 l 0,35 l
Weight 1,350 g 1,350 g 1,350 g 1,350 g 1,350 g 1,350 g 1,350 g
Dimensions 183 x 290 x113 mm
The power consumption data in the table and the other information given in the Product Data Sheet
(Enclosure A to this manual) are defined in relation to EU Directives 812/2013 and 814/2013.
The products without the label and the data sheet for water heaters and solar devices, stipulated in regulation
812/2013, are not intended to be used in such assemblies.
Products equipped with a regulator knob have the thermostat positioned in the <ready to use setting
indicated in the Data Sheet (Enclosure A), according to which the relevant energy class has been declared
by the manufacturer.
The product should be connected only to a supply with the relevant system impedance no more than
0.237 ohm.
Restrictions to connection may be imposed by the supply authority on the use of equipment in the
actual relevant system impedance at the interface point on the user's premise exceeds 0.237 ohm.
This appliance is conforming with the international electrical safety standards IEC 60335-1 and IEC
60335-2-35. When present, The CE marking of the appliances attests its conformity to the following EC
Directives, of which it satisfies the essential requisites:
- LVD Low Voltage Directive: EN 60335-1, EN 60335-2-35, EN 60529, EN 62233, EN 50106.
- EMC Electro-Magnetic Compatibility: EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3,
EN 61000-3-11 and EN 61000-3-12.
- ERP Energy related Products: Eu812, Eu814, EN50193-1-2013