manualshive.com logo in svg

Arista CCS-720XP Series, Quick Start Manual

Share
Download
Arista CCS-720XP Series Quick Start Manual Download Page 36

 

5. Verify the LED(s) on the power supply.

Note:  The Power Supply status LED is a steady green for normal operation.

6. Verify the new power supply operation by issuing the 

show environment power 

 command.

switch#

show environment power

The output of the command lists the power supplies in operation and includes the one you replaced.

E.2.2

 DC Power Supplies

Note:  Use a three-eighth inch (3/8") hexagon-socket wrench for removing the lug nuts.

E.2.2.1

 Removing a DC Power Supply

Before performing any of the steps, ensure power is removed from DC circuits by turning off the power
line servicing the circuits.

Note:  Make sure to remove the ground connection last when removing power.

1. Put on a grounded, anti-static ESD strap.
2. Disconnect the power cable from the DC power source.
3. Access the terminal studs by lifting the plastic cover.
4. Remove the flange locking nuts to each of the terminal studs.
5. Disconnect the power cable lug from the terminal studs.
6. Use the power supply release lever to unseat and slide out the power supply.

E.2.2.2

 Installing a DC Power Supply

You must make space for installing the power supply by removing an existing one (

Removing a DC

Power Supply

) from a power supply slot available on the switch. Perform the following steps to install a

DC power supply.

1. Put on a grounded ESD strap.
2. Unbox the new power supply.
3. Insert the new power supply into the empty power supply slot.
4. After you insert the power supply, push gently on the power supply until the power supply is fully

seated and locked in place.

5. Connect the DC-input wires to the appropriate terminals using the specified torque (

Table 6: Wiring,

Lug, and Tightening Torques for DC PSU

) in the following order:

a. Ground wire to the Protective Earth (PE ) terminal.

b. Negative source DC cable to the negative (- / -48V) terminal.

c. Positive (+) source DC cable to the positive (+ / Rtn) terminal.

E.3

 Fan Modules

Hot swap fans within 30 seconds to prevent the switch from overheating. Ensure that the module you
are replacing matches those already installed in the switch.

E.3.1

  Removing a Fan Module

The following steps are required when removing or replacing fans from a switch.

32

Summary of Contents for CCS-720XP Series











































Reviews:

No comments

Brands by name

Popular brands

Load more brands