manualshive.com logo in svg

Arista CCS-720XP Series, Quick Start Manual

Share
Download
Arista CCS-720XP Series Quick Start Manual Download Page 13

Chapter  3

Rack Mounting the Switch

The Rack Mounting the Switch section reviews the following topics:

•

Two-Post or Four-Post Rack Mount

•

Attaching Mounting Brackets to the Chassis

•

Inserting the Switch into the Rack

Note:  The rack mounting procedure is identical for all switches covered by this guide.
Illustrations in this chapter depict the mounting of a DCS-7010T-48 switch.

Les procédure de montage du bâti est identique pour tous les commutateurs visés par ce
guide. Illustrations dans ce chapitre montrent le montage d’un interrupteur de DCS-7010T-48.

•

Two-Post or Four-Post Rack Mount

 provides instructions for mounting the switch in a two-post rack

or four-post rack.

After completing the instructions for your rack type, proceed to 

Cabling the Switch

.

Note:  Illustrations use a representative Arista switch. Your device may be different in
appearance.

3.1

 Two-Post or Four-Post Rack Mount

The switch can be installed in a two-post or four-post rack. The installation process is identical
because the switch attaches to only two posts of a rack.

To mount the switch in a rack, assemble the mounting brackets to the chassis, then attach the
brackets to the rack posts. Rack mount accessory kits include the following parts:

•

2 x mounting brackets

•

6 x M4x5 flat head Phillips screws.

The following image displays the proper bracket placement for the rack mount.

Figure 3: Bracket Mount Placement for Rack Mount

3.1.1

 Attaching Mounting Brackets to the Chassis

This procedure attaches mounting brackets to the switch chassis.

1. Align the mounting brackets with the chassis holes at the front of the switch.
2. Attach the brackets with two M4x5 flat head Philips screws.

9

Summary of Contents for CCS-720XP Series











































Reviews:

No comments

Brands by name

Popular brands

Load more brands