manualshive.com logo in svg

Arista CCS-720XP Series, Quick Start Manual

Share
Download
Arista CCS-720XP Series Quick Start Manual Download Page 25

Status Indicators

LED State

Status

Yellow

Port is software disabled.

Flashing Yellow

Port failed diagnostics.

A.2

 Rear Status Indicators

Fan and power supply modules are accessed from the rear panel. Each fan and power supply module
contains an LED that reports the module status.

Fan Status LEDs are on the fan modules, as displayed in 

Figure 13: Fan Status LED

.

Figure 13: Fan Status LED

1 Fan module status LED

Table 10: Fan Status LED States (Rear)

 provides status conditions that correspond to fan status LED

states.

Table 10: Fan Status LED States (Rear)

LED State

Status

Off

The fan module is not
detected. If it is inserted, it
may not be seated properly.

Green

The fan is operating normally.
This LED state is exclusive
to its fan module, and
independent of the states of
its neighboring fans and power
supplies.

Red

The fan has failed.

The AC Power Supply Status LEDs are on the power supply modules, as displayed in 

Figure 14:

Representative AC Power Supply Status LED (PWR-1021-AC-RED)

.

21

Summary of Contents for CCS-720XP Series











































Reviews:

No comments

Brands by name

Popular brands

Load more brands