background image

otherwise, automatic  halt can be brought about.  At this point,  re-start the 

fan only. 

 

16.  The  applicable  temperature  range  is  -20

  to  40

.  The  water  in  the 

tank  is  easy  to  deteriorate  and  give  off-flavor,  so  please  change  water 

regularly. 

17. Do not put the fan under the power plug directly. 

18. Do not use the fan around the bath, shower nozzle or swimming pool. 

19.  The  fan  is  qualified  to  be  maintained  at  the  specified  maintenance 

shops. 

 

 

VI.

 

Cleaning and Maintenance 

 

 

★★★

Kind  Reminder:

  Over  a  long  period  of  running,  the  wind 

capacity and dust removing effects of the filter screen and wet curtain 

are  inefficient  because  of  dust  block.  So  it  is  overwhelmingly 

recommended cleaning them regularly.       

1. Clean the air filter 

Cut  off  the  power  supply  and  unscrew  the  fan  with  a  manual 

screwdriver.  Then  the  filter  screen  can  be  dismounted.  Take  mild 

detergent and banister brush to clean the screen and wash it with clean 

water,  finally,  make  sure  that  the  filter  is  completely  dry  before 

operating the unit.   

2. Clean the wet curtain 

Firstly,  cut  off  the  power  supply,  and  then  get  the  air  filter  screen 

down in order to take out the wet curtain from back cover. Next, use 

mild detergent and banister brush to clean the wet curtain and wash it 

with clean water, finally, dry it. 

3. Clean the water tank 

Cut  off  the  power  supply;  take  the  air  filter  screen  down,  and  then 

take out the water tank. The following is to remove the dirt in the tank 

by using a towel with a few detergents,. After that,  wash and rinse it 

with clean water, wipe it with a piece of dry cloth, finally, dry it. 

4. Clean the outer cover 

Clean the outer cover with a mild detergent and a piece of soft cloth. 

★★★

Attention:

 

 

Cut off the  power  supply before  cleaning  the  fan due to  the  high 

voltage in it. 

 

No water in any part of the control panel.   

Wet curtain 

Air filter   

Summary of Contents for ARICOOL2H







Reviews: