arietta ASG430SSA Installation Instruction Manual Download Page 2

2

Table of Contents 

Important Safety Notice........................................................ 2
Tools and Parts...................................................................... 3
Dimensions and Clearances................................................. 3
Electrical  Requirements........................................................ 4
Venting Requirements........................................................... 4
Venting Methods.................................................................... 4
Installation  Instructions......................................................... 5
Electrical Connection............................................................ 8
Hood  Description................................................................... 9
Range Hood Care................................................................... 9
Warranty.................................................................................. 10

APPROVED FOR RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

 

IMPORTANT: 

 Save these Instructions for the Local Electrical 

 

Inspector’s use.

INSTALLER: 

 Please leave these Instructions with this unit for

 

the owner.

OWNER:

 Please retain these instructions for future 

 reference.

Safety Warning:

Turn off power circuit at service panel and lock 

out panel before wiring this appliance.

Requirement 120 VAC, 60 Hz. 15 or 20 A Branch Circuit 

IMPORTANT SAFETY INSTRUCTIONS

WARNING: 

TO REDUCE THE RISK OF FIRE, ELECTRIC 

SHOCK, OR INJURY TO PERSONS, OBSERVE THE  
FOLLOWING:

 

Use this unit only in the manner intended by the  

 

manufacturer. If you have questions, contact the 

 manufacturer.

 

Before servicing or cleaning the unit, switch power off at 

 

service panel and lock the service disconnecting means to  

 

prevent power from being switched on accidentally. When 

 

the service disconnecting means cannot be locked, securely 

 

fasten a prominent warning device, such as a tag to the 

 

service panel.

 

Installation work and electrical wiring must be done by  

 

qualified person(s) in accordance with all applicable codes  

 

and standards, including fire-rated construction.

 

Sufficient air is needed for proper combustion and  

 

exhausting of gases through the flue (chimney) of fuel  

 

burning equipment to prevent backdrafting. Follow the  

 

heating equipment manufacturer’s guideline and safety  

 

standards such as those published by the National Fire 

 

Protection Association (NFPA), the American Society for  

 

Heating, Refrigeration and Air Conditioning Engineers  

 

(ASHRAE), and the local code authorities.

 

When cutting or drilling into wall or ceiling; do not damage 

 

electrical wiring and other hidden utilities.

 

Ducted fans must always be vented outdoors.

CAUTION: 

For general ventilating use only. Do not use to 

exhaust hazardous or explosive materials and vapors.

CAUTION: 

To reduce risk of fire and to properly exhaust air, 

be sure to duct air outside - do not vent exhaust air into
spaces within walls or ceilings, attics or into crawl spaces, or
garages. 

WARNING:

 TO REDUCE THE RISK OF FIRE, USE ONLY METAL 

DUCTWORK

WARNING: 

TO REDUCE THE RISK OF A RANGE TOP  

GREASE FIRE:

 

Never leave surface units unattended at high settings. 

 

Boilovers cause smoking and greasy spillovers that may 

 

ignite. Heat oils slowly on low or medium settings.

 

Always turn hood ON when cooking at high heat or when  

 

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,  

 

Peppercorn Beef Flambé).

 

Clean ventilating fans frequently. Grease should not be  

 

allowed to accumulate on fan or filter.

 

Use proper pan size. Always use cookware appropriate for  

 

the size of the surface element.

WARNING:

 TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, 
OBSERVE THE FOLLOWING:

a

 

SMOTHER FLAMES with a close fitting lid, cookie sheet, or 

 

metal tray, then turn off the burner. BE CAREFUL TO  

 

PREVENT BURNS. If the flames do not go out  

 

immediately, EVACUATE AND CALL THE FIRE  

 DEPARTMENT.

 

NEVER PICK UP A FLAMING PAN - you may get burned.

 

DO NOT USE WATER, including wet dishcloths or towels -  

 

a violent steam explosion will result.

 

Use an extinguisher ONLY if:

-You know you have a class ABC extinguisher, and you 

 

already know how to operate it.

 

– The fire is small and contained in the area where it

 started.
 

– The fire department is being called.

 

– You can fight the fire with your back to an exit. 

a

Based on “Kitchen Fire Safety Tips” published by NFPA.

WARNING: 

To reduce the risk of fire or electrical shock, 

do not use this fan with any solid-state speed control device.

READ AND SAVE THESE INSTRUCTIONS

Summary of Contents for ASG430SSA

































Reviews: