background image

GB-16

*

 Change oil after first 8 hours of operation and every 100 

hours thereafter.

**

 Change Hydraulic Fluid after first 50 hours of operation 

and every 500 hours thereafter.

MAINTENANCE SCHEDULE

Period

Service

Task

Each Use

Check Safety Interlock System

WARNING: 

Safety interlock system failure and improper operation of unit 

can result in death or serious injury. Test this system each time the unit is 
operated. If this system does not function as described, do not operate until 
repairs are made. See Check Safety Interlock System on page 11.

Check Air Cleaner

Check the air cleaner element before each use. See engine manual for 
detailed instructions.

Check Engine Oil

Check the engine oil level before each use. Never operate the engine when 
the oil level is low. See engine manual for detailed instructions.

Check Engine Cooling

Check the engine air cooling system before each use. See engine manual for 
detailed instructions.

Check Fasteners

Check all nuts, bolts, and other fasteners before each use. Replace missing 
or damaged fasteners.

Check Tire Pressure

Check tires for proper inflation, excessive wear or damage before each use. 
The correct air pressure is 8 to 16 psi (55 to 110 kPa).

Check Hydraulic Fluid Level

Check hydraulic oil level mark on cap/dipstick. Add 15W-50 synthetic oil as 
needed. Do not overfill.

Follow Engine Manual 
Maintenance Schedule

Perform scheduled engine maintenance. See engine manual for detailed 
instructions.

Check Battery

Keep battery and its terminals clean. 

Every 25 

Hours

Check All Belts

Replace worn or deteriorated belts. 

Mower Blades

Check mower blades for wear. Sharpen or replace as needed.

Clean Air Cleaner Foam 
Element

See engine manual for detailed instructions.

Every 50 

Hours

General Lubrication

All all pivot points and pin connections. Grease lube fittings.

Every 100 

Hours

Change Engine Oil

Open the petcock to drain oil through oil drain hole on the left side of engine. 
See engine manual for addional instructions.

Check Fuel Filter

See engine manual for detailed instructions.

Check Spark Plug

See engine manual for detailed instructions.

Check Muffler

Check muffler for damage or wear. Replace if necessary.

Clean Air Cleaner Paper 
Element

See engine manual for detailed instructions.

Every 500 

Hours

Change Hydraulic Fluid and 
Filter

Drain hydraulic tank, replace hydraulic oil filter, refill system. 

Summary of Contents for 988316



























Reviews: