background image

EN - 17

CONTROLS AND FEATURES

See Figure 16 for all Controls and Features 
locations.

Dual Handle Interlock 

When Attachment Clutch and then Traction 
Drive Clutch are engaged, the Attachment 
Clutch will remain engaged (lever down) if 
released. To stop attachment, release 
Traction Drive Clutch and both clutches will 
disengage.

Traction Drive Clutch – Left Hand 
Lever

Squeeze the Traction 
Drive Clutch Lever 
against the Handlebar 
(1) to engage wheel 
drive for propelling unit. 
Forward speed will 
vary according to snow 
depth and moisture 
content. 

Release lever (2) to stop movement.

NOTICE: 

When traveling to or from the area 

to be cleared, press down on the handlebars 
enough to raise the front of the unit slightly off 
the surface. Engage the traction drive clutch 
without engaging the attachment drive clutch.

Attachment Clutch – Right Hand 
Lever

Squeeze Attachment 
Clutch Lever against 
handlebar (1) to 
engage attachment. 
Release both clutch 
levers (2) to disengage 
power and apply brake 
to attachment.

IMPORTANT: 

If the belt squeals continuously 

when the attachment clutch lever is engaged, 
the impeller may be frozen in the auger 
housing. Immediately release the attachment 
clutch lever and move the unit into a heated 
area to thaw.

NOTICE: 

If belt squeals continuously when 

impeller turns freely, see 

Attachment 

Clutch/Brake Adjustment

 on page 28.

Ignition Switch

Operate the ignition switch with the 
removable key. To start the engine, turn the 
key to Start (1). To stop the engine, turn the 
key to Off (2).

Primer Bulb

Pushing the primer bulb in adds fuel for 
easier engine start. Refer to 

Starting and Shut 

Off

 on page 20.

Speed Selector

Position the Speed Selector in the 
appropriate speed notch to control forward 
and reverse travel.

Forward:
(6) Fastest

(1) Slowest 

Reverse: 
(1) Slow

(2) Fast

IMPORTANT: 

DO NOT change 

motion from forward to reverse 
with clutch engaged. Forward 
speed can be changed without 
declutching.

OPERATION

WARNING: 

AVOID INJURY. Read 

and understand the entire 

Safety

 

section before proceeding.

WARNING: 

To avoid injury to hands 

and feet, always disengage 
clutches, shut off engine, and wait 
for all movement to stop before 
unclogging or working on snow 
thrower.
Keep hands and feet away from 
auger and impeller.

1

2

1

2

2

1

6

1

1

2

Summary of Contents for 921029









































Reviews: