Ariens 915209 - Zoom 34 CARB Operator'S Manual Download Page 21

EN - 21

IMPORTANT: 

Proper maintenance can 

prolong the life of unit. The following chart 
shows the recommended service schedule. 
Refer to the maintenance instructions in the 
Engine Manual for additional information.

NOTICE: 

To have full access to the engine, 

the seat must be tipped forward (see 

Tipping 

Seat Forward 

on page 23) and the hood 

opened (see 

Opening and Closing Hood 

on 

page 23).

MAINTENANCE 

SCHEDULE

WARNING: 

AVOID INJURY. Read 

and understand the entire 

Safety

 

section before proceeding.

Interval

Task

Action

Each Use

Check 
Safety 
Interlock 
System

WARNING: 

Safety interlock system failure and improper 

operation of unit can result in death or serious injury. Test 
this system each time the unit is operated. If this system 
does not function as described, do not operate until repairs 
are made. See 

Safety Interlock System 

on page 16.

Check 
Parking 
Brake

Engage parking brake and engage transmission bypass lever. See 

Moving Unit Manually 

on page 20. Push unit. If unit rolls, contact your 

Ariens dealer.

Clean 
Unit

Clean engine, battery, seat, etc. of all dirt and debris. Do not use 
solvents, hard cleaners, or abrasives. For deck cleaning instructions, 
see 

Washout Port 

on page 18.

NOTE: 

Protect painted surfaces with automotive type wax.

IMPORTANT: 

Do not spray the unit with water, especially when the 

unit is warm from operation.

Check 
Tires

See Specifications on page 35 for correct tire pressure.

CAUTION: 

Avoid injury! Explosive separation of tire and rim 

parts is possible when they are serviced incorrectly: 

Do not attempt to mount a tire without the proper equipment 
and experience to perform the job. 

Do not inflate the tires above the recommended pressure. 

Do not stand in front or over the tire assembly when inflating. 
Use a clip-on chuck and extension hose long enough to allow 
you to stand to one side. 

Check 
Mower 
Blades

Check for worn or damaged mower blades. See 

Sharpening Mower 

Blade 

on page 26.

Each Use

Follow 
Engine 
Manual 
Mainten-
ance 
Schedule

Perform scheduled engine maintenance. 
Refer to Engine Manual for detailed 
instructions.

NOTICE: 

To drain the oil, remove oil 

drain cap and attach the oil drain hose, 
supplied in the lit pack, to the drain plug. 
Rotate the drain to the left to allow oil to 
drain. Turn the drain to the right to close.

Oil Drain Plug

Summary of Contents for 915209 - Zoom 34 CARB









































Reviews: