Ariens 915209 - Zoom 34 CARB Operator'S Manual Download Page 11

EN - 11

DO NOT park on slopes unless necessary. 
When parking on slope ALWAYS chock or 
block wheels. ALWAYS set parking brake.

Choose a low ground speed so you will not 
have to stop or shift while on a slope.

DO NOT mow near drop-offs, ditches, or 
embankments. The machine could suddenly 
roll over if a wheel goes over the edge or if 
the edge caves in.

DO NOT bypass transmission or allow 
transmission to free-wheel when on a slope. 

Fuel

To avoid personal injury or property damage, 
use extreme care in handling gasoline. 
Gasoline is extremely flammable and the 
vapors are explosive.

Ethanol blends must not exceed E10. Higher 
ethanol content may cause your 
machine to run hotter and damage your 
engine.

Replace fuel cap securely and clean up 
spilled fuel before starting engine.

Extinguish all cigarettes, cigars, pipes and 
other sources of ignition.

Use only an approved gasoline container.

NEVER store the machine or fuel container 
where there is an open flame, spark or pilot 
light such as on a water or space heater or 
other appliances.

NEVER fill containers inside a vehicle or on 
a truck or trailer bed with a plastic liner. 
ALWAYS place containers on the ground 
away from your vehicle before filling.

NEVER fuel the machine indoors.

NEVER remove gas cap or add fuel with the 
engine running. Allow engine to cool before 
fueling.

Fuel is highly flammable and its vapors are 
explosive. Handle with care. Use only an 
approved gasoline container with an 
appropriately-sized dispensing spout.

NO smoking, NO sparks, NO flames. 

Remove gas-powered equipment from the 
trailer and refuel it on the ground. If this is 
not possible, then refuel such equipment 
with a portable container, rather than from a 
gasoline dispenser nozzle.

Keep the nozzle in contact with the rim of 
the fuel tank or container opening at all 
times until the fueling is complete. DO NOT 
use a nozzle lock-open device.

NEVER overfill fuel tank. Replace gas cap 
and tighten securely.

If fuel is spilled on clothing, change clothing 
immediately.

Towing

Follow the manufacturer’s recommendations 
for weight limits for towed equipment and 
towing on slopes.

NEVER allow children or others in or on 
towed equipment.

Tow only with a machine that has a hitch 
designed for towing. DO NOT attach towed 
equipment except at the hitch point.

On slopes, the weight of the towed 
equipment may cause loss of traction and 
loss of control.

Travel slowly and allow extra distance to 
stop.

Accessories

Follow the manufacturer’s recommendation 
for wheel weights or counterweights

Check grass catcher components and the 
discharge guard frequently and replace with 
the manufacturer’s recommended parts, 
when necessary.

Use only Ariens Company-recommended 
attachments that are appropriate to your use 
and can be used safely in your application.

Batteries

Avoid electric shock. Objects contacting 
both battery terminals at the same time may 
result in injury and unit damage. DO NOT 
reverse battery connections.

Reverse connections may result in sparks 
which can cause serious injury. ALWAYS 
connect positive (+) lead of charger to 
positive (+) terminal, and negative (-) lead to 
negative (-) terminal.

ALWAYS disconnect negative (-) cable 
FIRST and positive (+) cable SECOND. 
ALWAYS connect positive (+) cable FIRST, 
and negative (-) cable SECOND.

Explosive gases from battery can cause 
death or serious injury. Poisonous battery 
fluid contains sulfuric acid and its contact 
with skin, eyes or clothing can cause severe 
chemical burns.

No flames, No sparks, No smoking near 
battery.

Summary of Contents for 915209 - Zoom 34 CARB









































Reviews: