ARI ARI-PACO 2G Operating And Installation Instructions Download Page 1

0040501006 2422 english (englisch)

- Translated original instructions -

1.0 General information on operating instructions............................................................................................. 2-3
2.0 Notes on possible dangers ............................................................................................................................. 2-3

2.1  Significance of symbols  ........................................................................................................................... 2-3
2.2  Explanatory notes on safety information................................................................................................... 2-4

3.0 Storage and transport ..................................................................................................................................... 2-4
4.0 Description ....................................................................................................................................................... 2-5

4.1  Field of application .................................................................................................................................... 2-5
4.2  Method of functioning................................................................................................................................ 2-5
4.3  Diagram .................................................................................................................................................... 2-6

4.3.1 ARI-PREMIO

®

-Plus 2G 2,2 - 5 kN ................................................................................................... 2-6

4.3.2 ARI-PREMIO

®

-Plus 2G 12 - 25 kN .................................................................................................. 2-7

4.3.3 Parts list ........................................................................................................................................... 2-8

4.4  Technical data ........................................................................................................................................... 2-9
4.5  Interface description................................................................................................................................ 2-12

4.5.1 Control - Run commands  .............................................................................................................. 2-12
4.5.2 Feedback   ..................................................................................................................................... 2-13
4.5.3 Design notes.................................................................................................................................. 2-14

4.6  Dimensions ............................................................................................................................................. 2-17

Operating and Installation Instructions

 

Thrust actuator 

ARI-PREMIO

®

-Plus 2G

Contents

Summary of Contents for ARI-PACO 2G





















































Reviews: