Argos Malibu 305/1788 Assembly Instructions Manual Download Page 39

Page: 39 / 48

Insert drawer

Lift front of drawer whilst

inserting to overcome

the ‘stop’ system.

Note:

To ensure that

your drawer runs

smoothly, spray a small

amount of furniture

polish into the grooves.

Assembly Instructions

Step

Prepare left and right

side

Separate runners .

Push fit the left

runner marked ‘

’ into

the holes shown on left

side .

Note:

Runners must be

be fitted flat against the

panel. If necessary

gently tap into final

position.

Insert large locking

nut as shown.

Note:

Arrow on locking

nut

must

point towards

hole in edge of panel.

Tap in wooden dowel

as shown.

Note:

Wooden dowels

must not

stick out from

the edge by more than

10mm or they may

damage other panels.

Push fit the right

runner marked ‘

’

into the holes shown on

left side .

Insert large locking

nut as shown.

Tap in wooden dowel

as shown.

Step

Fit the hanging rails

and drawers

Push the large hanging

rail and 2 small

hanging rails into the

rail holders .

Lift front of drawer whilst

inserting to overcome

the ‘stop’ system.

Note:

To ensure that

your drawer runs

smoothly, spray a small

amount of furniture

polish into the grooves.

x 4

Fit the shelf studs

For each of the 2

loose shelves , insert

4 shelf studs .

x 4

Summary of Contents for Malibu 305/1788

















































Search results

Summary of Contents for Malibu 305/1788

Reviews:

Related manuals for Malibu 305/1788

Brands by name

Popular brands

Argos Malibu 305/1788, Assembly Instructions Manual

Search results

Summary of Contents for Malibu 305/1788

Reviews:

Related manuals for Malibu 305/1788

Brands by name

Popular brands