background image

 

V 11/17 

51 

2. 

Drill the holes for the screws in the wall with a hammer drill (the drill bit must match the plastic wall 

plug). Then insert the wall plugs into the holes.  

3.  Secure  the  plate  to  the  wall  with  the  self-tapping  screws  (ST4.2X25TA).  Check  it  is  securely 
attached by pulling on the bracket. If a plastic wall plug is loose, drill another hole nearby with the 
hammer drill. 
 

Step three: drill the hole for the piping 

Select the position for the piping hole according to the direction of the outlet pipe. The piping hole 
must be slightly lower than the wall-installation frame, as shown below. 
 

   09K -12K                                                           

 

Drill  a  piping  hole  of  diameter 

55  or  70 

at  the  chosen  location  for  the  outlet  pipe.  To  allow  for 

proper drainage, the piping hole in the wall must slant slightly downwards to the outdoor side, with a 
gradient of 5 – 10°. 
 

 

Piping hole 

Model 

Ø 55 

Cooling capacity < 6000 W 

 
N.B.: 

• 

Take  the  necessary  safety  measures  when 

drilling  the  hole  and  do  not  allow  dust  to 
enter. 

• 

The  plastic  wall  plugs  are  not  supplied  but 

must be purchased on site. 
 
 

 

 

 

Indoors 

 

Outdoors 

 
 

Step four: outlet pipe 

The pipe can be brought out in various different 
directions: right, rear right, left or rear left. 

 

destra 

right 

Posteriore destra 

rear right 

sinistra 

left 

Posteriore sinistra 

rear left 

 

Once  you  have  selected  the  direction  of  the 
outlet  (left  or  right),  drill  the  corresponding 
hole at the bottom.

 

 

 

destra 

right 

foro da praticare 

hole to be drilled 

sinistra 

left 

 

Interno

5-10

Esterno

Φ55

sinistra posteriore

sinistra

destra

posteriore

destra

foro da
praticare

sinistra

destra

Summary of Contents for Ecolight 12000 UI

































Reviews: