Argo ADG ECO PLUS 100PH Installation Manual Download Page 58

Page: 58 / 70

Duct Type Unit

NOTE:

Check the above items and adopt the corresponding corrective

measures. If the air conditioner continues to function poorly, please stop the air
conditioner immediately and contact Gree’s authorized local service center. Ask our
professional service staff to check and repair the unit.

5.2 Error Code

WARNING!

(1) If abnormal things (for example, awful smell) occur, please stop the unit

immediately and disconnect power. Then contact Gree’s authorized service

center. If the unit continues to run in abnormal situations, it may get damaged

and cause electric shock or fire hazard.

(2) Do not repair the air conditioner by yourself. Improper maintenance will cause

electric shock or fire hazard. Please contact Gree’s authorized service center

and send for professional service staff to repair.
If the display panel or wired control displays an error code, please refer to the

error code meaning stated in the following table.

Error code

Error

code

Error

Outdoor fan IPM module

protection

Compressor overspeed

Outdoor fan startup failure

Power protection

Outdoor fan Phase-loss

protection

IDU and ODU unmatched

Outdoor fan current

detection circuit error

ODU error, for specific error

please see the status of ODU

main board indicator

Outdoor fan out-of-step

protection

Driver reset protection

Wired controller and indoor

unit communication failure

Compressor phase

over-current protection

Indoor ambient temperature

sensor error

Master control and driver

communication error

Evaporator temperature

sensor error

Module temperature sensor

circuit failure

Condenser temperature

sensor error

Driver module temperature

protection

ODU jumper cap error

AC contractor protection

IDU jumper cap error

ODU AC current protection

Summary of Contents for ADG ECO PLUS 100PH







































































Search results

Summary of Contents for ADG ECO PLUS 100PH

Reviews:

Brands by name

Popular brands

Argo ADG ECO PLUS 100PH, Installation Manual

Search results

Summary of Contents for ADG ECO PLUS 100PH

Reviews:

Brands by name

Popular brands