background image

Argo Service Manual                       Ducting & Exhaust

Ontario Drive & Gear Limited                                                                                            www.odg.com
PH.(519)- 662-2840   FAX (519)- 662-2421

DE-1

      SECTION DE

           Ducting & Exhaust

                   Table of Contents

General Instructions............................................................................. DE-2
Removing the Muffler
(Conquest Models Prior to C19672).................................................... DE-3
Disassembling the Muffler Assembly
(Conquest Models Prior to C19672).................................................... DE-5
Assembling the Muffler Assembly
(Conquest Models Prior to C19672).................................................... DE-6
Removing the Muffler (Conquests from C19672).............................. DE-7
Installing the Muffler (Conquests from C19672)............................... DE-8
Removing the Muffler (Response, Vanguard2 & Vanguard)............ DE-8
Installing the Muffler (Response, Vanguard2 & Vanguard)............. DE-10
Remove the Muffler (Bigfoot Models).................................................DE-11
Installing the Muffler (Bigfoot Models).............................................. DE-11
Spark Arrestor Information & Maintenance..................................... DE-11
Removing the Intake Duct
(Response, Bigfoot, Vanguard2 & Vanguard).................................... DE-12
Installing the Intake Duct
(Response, Bigfoot, Vanguard2 & Vanguard).................................... DE-13
Removing the Intake Duct (Conquest Models)...................................DE-13
Installing the Intake Duct (Conquest Models)....................................DE-14
Removing the Exhaust Ducting
(Response, Bigfoot, Vanguard2 & Vanguard).................................... DE-14

Installing the Exhaust Ducting
(Response, Bigfoot, Vanguard2 & Vanguard Models)........................DE-14

Summary of Contents for 6x6 Conquest

















Reviews: